World India tops 200,000 dead as virus surge breaks health system

tom_mai78101

The Helper Connoisseur / Ex-MineCraft Host
Staff member
Reaction score
1,667
NEW DELHI (AP) — India crossed a grim milestone Wednesday of 200,000 people lost to the coronavirus as a devastating surge of new infections tears through dense cities and rural areas alike and overwhelms health care systems on the brink of collapse.

The health ministry reported a single-day record 3,293 COVID-19 deaths in the last 24 hours, bringing India’s total fatalities to 201,187, as the world’s second most populous country endures its darkest chapter of the pandemic yet.

The country also reported 362,757 new infections, a new global record, which raised the overall total past 17.9 million. The previous high of 350,000 on Monday had capped a five-day streak of recording the largest single-day increases in any country throughout the pandemic.

India, a country of nearly 1.4 billion people, is the fourth to cross 200,000 deaths, behind the United States, Brazil and Mexico. And as in many nations, experts believe the coronavirus infections and fatalities in India are severe undercounts.

The first known COVID-19 death in India happened on March 12, 2020, in southern Karnataka state. It took five months to reach the first 50,000 dead. The toll hit 100,000 deaths in the next two months in October 2020 and 150,000 three months later in January this year. Deaths slowed until mid-March, only to sharply rise again.

For the past week, more than 2,000 Indians have died every day.


Read more here. (Associated Press)
 
General chit-chat
Help Users
  • No one is chatting at the moment.
  • Varine Varine:
    How can you tell the difference between real traffic and indexing or AI generation bots?
  • The Helper The Helper:
    The bots will show up as users online in the forum software but they do not show up in my stats tracking. I am sure there are bots in the stats but the way alot of the bots treat the site do not show up on the stats
  • Varine Varine:
    I want to build a filtration system for my 3d printer, and that shit is so much more complicated than I thought it would be
  • Varine Varine:
    Apparently ABS emits styrene particulates which can be like .2 micrometers, which idk if the VOC detectors I have can even catch that
  • Varine Varine:
    Anyway I need to get some of those sensors and two air pressure sensors installed before an after the filters, which I need to figure out how to calculate the necessary pressure for and I have yet to find anything that tells me how to actually do that, just the cfm ratings
  • Varine Varine:
    And then I have to set up an arduino board to read those sensors, which I also don't know very much about but I have a whole bunch of crash course things for that
  • Varine Varine:
    These sensors are also a lot more than I thought they would be. Like 5 to 10 each, idk why but I assumed they would be like 2 dollars
  • Varine Varine:
    Another issue I'm learning is that a lot of the air quality sensors don't work at very high ambient temperatures. I'm planning on heating this enclosure to like 60C or so, and that's the upper limit of their functionality
  • Varine Varine:
    Although I don't know if I need to actually actively heat it or just let the plate and hotend bring the ambient temp to whatever it will, but even then I need to figure out an exfiltration for hot air. I think I kind of know what to do but it's still fucking confusing
  • The Helper The Helper:
    Maybe you could find some of that information from AC tech - like how they detect freon and such
  • Varine Varine:
    That's mostly what I've been looking at
  • Varine Varine:
    I don't think I'm dealing with quite the same pressures though, at the very least its a significantly smaller system. For the time being I'm just going to put together a quick scrubby box though and hope it works good enough to not make my house toxic
  • Varine Varine:
    I mean I don't use this enough to pose any significant danger I don't think, but I would still rather not be throwing styrene all over the air
  • The Helper The Helper:
    New dessert added to recipes Southern Pecan Praline Cake https://www.thehelper.net/threads/recipe-southern-pecan-praline-cake.193555/
  • The Helper The Helper:
    Another bot invasion 493 members online most of them bots that do not show up on stats
  • Varine Varine:
    I'm looking at a solid 378 guests, but 3 members. Of which two are me and VSNES. The third is unlisted, which makes me think its a ghost.
    +1
  • The Helper The Helper:
    Some members choose invisibility mode
    +1
  • The Helper The Helper:
    I bitch about Xenforo sometimes but it really is full featured you just have to really know what you are doing to get the most out of it.
  • The Helper The Helper:
    It is just not easy to fix styles and customize but it definitely can be done
  • The Helper The Helper:
    I do know this - xenforo dropped the ball by not keeping the vbulletin reputation comments as a feature. The loss of the Reputation comments data when we switched to Xenforo really was the death knell for the site when it came to all the users that left. I know I missed it so much and I got way less interested in the site when that feature was gone and I run the site.
  • Blackveiled Blackveiled:
    People love rep, lol
    +1
  • The Helper The Helper:
    The recipe today is Sloppy Joe Casserole - one of my faves LOL https://www.thehelper.net/threads/sloppy-joe-casserole-with-manwich.193585/
  • The Helper The Helper:
    Decided to put up a healthier type recipe to mix it up - Honey Garlic Shrimp Stir-Fry https://www.thehelper.net/threads/recipe-honey-garlic-shrimp-stir-fry.193595/

      The Helper Discord

      Members online

      No members online now.

      Affiliates

      Hive Workshop NUON Dome World Editor Tutorials

      Network Sponsors

      Apex Steel Pipe - Buys and sells Steel Pipe.
      Top