N-504 photos
- Thread starter Bolid
- Start date
Thank you.
Cobra!
New Member
- Reaction score
- 5
I’m jealous! I would love an N-504 or N-505 because I live in a PAL country.
I have to use an N-501 because that was all I could find so far. Still going around second hand shops in hopes of finding a PAL model one day...
Does that cover on the left cover anything? I heard PAL units don’t have controller ports.
I have to use an N-501 because that was all I could find so far. Still going around second hand shops in hopes of finding a PAL model one day...
Does that cover on the left cover anything? I heard PAL units don’t have controller ports.
On N-504 cover covers two gameports. So - N-504 has gameports! N-505 does not have gameports but you can add them - check my article on Nuon-dome! N-504 was sold in Switzerland - maybe you can find used there - online.
- No one is chatting at the moment.
-
Varine:
I'm now realizing I could have cut out like 99% of this print and it would have been fine cuz I just need to see if a frame will fit over an LCD -
-
-
-
The Helper:
I love the whole concept of 3D Printers and am very happy you have one so I can hear about them -
The Helper:
897K views · 27K reactions | Follow for funny clips #comedy #craig #ferguson #rizz #funny #talkshow #killtonypodcast #killtony #funny #fyp #podcasting #reels2024 #comedy #killtonypodcast #killtony #comedian #comedy #funny #standupcomedy #memes #expl
Follow for funny clips #comedy #craig #ferguson #rizz #funny #talkshow #killtonypodcast #killtony #funny #fyp #podcasting #reels2024 #comedy #killtonypodcast #killtony #comedian #comedy #funny...www.facebook.com
-
-
Varine:
So I picked the biggest one. When I bought it, I didn't realize that they used a lot of proprietary parts. So, I want to use these Volcano nozzles that are really cheap and easy to find instead of what they have, which are like, modified Volcano nozzles
-
Varine:
They are just a little bit longer than the regular ones. Like, we're talking .5mm or some shit. But that little bit makes the nozzle just long enough to extrude past the rest of the hardware on the extrusion system, I can't find my notes on it but I think it's like a .25mm gap from the end of the nozzle to the bed mesh sensor. Very small.
-
Varine:
So I bought a bunch of different parts to try and figure out how to make this work, and in the process changed some of the electrical components like the thermistors, but never got around to figuring out how to make the firmware account for the different hardware. Resulting in it not interpreting the voltage change to mean that the thermistor was above temperature, so it didn't shut off the heating core and it just kept pumping heat out
-
Varine:
I have most of the stuff I need to build an enclosure so I can heat the chamber for different plastics that need to have a pretty consistent temperature through the whole model, and then I can get my other ones set up too. I have a shitty Ender but that one is super easy to modify, but it's also very outdated and kind of a nightmare to work with. I think I'm going to cannibalize it for parts and just run my big one and another little one.
-
-
Varine:
Like Super 8 reels. Actual equipment to do it is like, thousands and thousands of dollars, and the cheap ones are useless, so I'm trying to build one so I can just use the same camera I use for slides and negatives. Much cheaper
-
Varine:
Anyway, it kind of works, but the take up reel is kind of tricky because you need to spin it directly to wind the tape onto it. And as it fills, you need to slow it down, and that's kind of complicated. More complicated than I wanted to try and account for, anyway.
-
Varine:
So I have the first motor that has gearing pull it from the original reel, through a set of pullies to keep some tension, and then a second motor synced with the first to guide it through the projection port so I can capture the images
-
Varine:
All that's easy enough, I just need to make sure I don't get too much force onto the film itself so I don't accidentally tear it.
-
Varine:
Then I think my solution to the take up reel is to have a kind of dancing lever on a spring in between two limit switches
-
Varine:
So, as the tape comes towards the take up reel and makes slack, that lever is pulled up by a spring to keep the tension on the film, it hits a limit switch to engage the take up reel motor at some point, and as that winds in the film, the film pushes the lever back down to a second limit switch to disengage the motor again. Slack builds up, spring pulls it back, ad infinitum
-
-
Varine:
I'm guessing it's going to be much harder than I feel like it is going to be right now, but I think it's a pretty elegant solution that doesn't rely on software to control it. The less software I need to use the better
-
-
The Helper:
Programming that printer is going to be similar to programming a big machine like in a machine shop. There is good money in programming CNC machines.
-
-
Varine:
They are pretty similar, but this one is much less involved than a real CNC. A lot less moving parts+1
-
The Helper Discord
Staff online
-
The HelperNecromancy Power over 9000
Share this page
Affiliates
Network Sponsors
Apex Steel Pipe - Buys and sells Steel Pipe.