Sci/Tech Replacing Electricity With Light: First Physical 'Metatronic' Circuit Created

Furby

Current occupation: News poster
Reaction score
144
The technological world of the 21st century owes a tremendous amount to advances in electrical engineering, specifically, the ability to finely control the flow of electrical charges using increasingly small and complicated circuits. And while those electrical advances continue to race ahead, researchers at the University of Pennsylvania are pushing circuitry forward in a different way, by replacing electricity with light.

The "meta" in "metatronics" refers to metamaterials, the relatively new field of research where nanoscale patterns and structures embedded in materials allow them to manipulate waves in ways that were previously impossible. Here, the cross-sections of the nanorods and the gaps between them form a pattern that replicates the function of resistors, inductors and capacitors, three of the most basic circuit elements, but in optical wavelengths.

"If we have the optical version of those lumped elements in our repertoire, we can actually make designs similar to what we do in electronics but now for operation with light," Engheta said. "We can build a circuit with light."

In their experiment, the researchers illuminated the nanorods with an optical signal, a wave of light in the mid-infrared range. They then used spectroscopy to measure the wave as it passed through the comb. Repeating the experiment using nanorods with nine different combinations of widths and heights, the researchers showed that the optical "current" and optical "voltage" were altered by the optical resistors, inductors and capacitors with parameters corresponding to those differences in size.

 
Last edited by a moderator:

Accname

2D-Graphics enthusiast
Reaction score
1,462
I guess the question is whether the gain in speed is adequate to the increase in power needed or the cost of the material.
Making a super fast computer is one thing, making a super fast computer which you can actually really build and dont need a nuclear power plant nearby to start it is a whole different story.
 

The Helper

Necromancy Power over 9000
Staff member
Reaction score
1,697
Tesla envisioned this type of thing but was shut out because they could not charge for it. Took them this long to "Discover it again"
 

T.s.e

Wish I was old and a little sentimental
Reaction score
133
Since light has a velocity, would sharp bumps upset this?
Since really hot materials glow, is this overly heat sensitive?
Hm. :)
Probably not more heat sensitive than things running on electricity in any case. If it gets hot enough that it starts glowing, it would probably break either way.
 
General chit-chat
Help Users
  • No one is chatting at the moment.
  • The Helper The Helper:
    The bots will show up as users online in the forum software but they do not show up in my stats tracking. I am sure there are bots in the stats but the way alot of the bots treat the site do not show up on the stats
  • Varine Varine:
    I want to build a filtration system for my 3d printer, and that shit is so much more complicated than I thought it would be
  • Varine Varine:
    Apparently ABS emits styrene particulates which can be like .2 micrometers, which idk if the VOC detectors I have can even catch that
  • Varine Varine:
    Anyway I need to get some of those sensors and two air pressure sensors installed before an after the filters, which I need to figure out how to calculate the necessary pressure for and I have yet to find anything that tells me how to actually do that, just the cfm ratings
  • Varine Varine:
    And then I have to set up an arduino board to read those sensors, which I also don't know very much about but I have a whole bunch of crash course things for that
  • Varine Varine:
    These sensors are also a lot more than I thought they would be. Like 5 to 10 each, idk why but I assumed they would be like 2 dollars
  • Varine Varine:
    Another issue I'm learning is that a lot of the air quality sensors don't work at very high ambient temperatures. I'm planning on heating this enclosure to like 60C or so, and that's the upper limit of their functionality
  • Varine Varine:
    Although I don't know if I need to actually actively heat it or just let the plate and hotend bring the ambient temp to whatever it will, but even then I need to figure out an exfiltration for hot air. I think I kind of know what to do but it's still fucking confusing
  • The Helper The Helper:
    Maybe you could find some of that information from AC tech - like how they detect freon and such
  • Varine Varine:
    That's mostly what I've been looking at
  • Varine Varine:
    I don't think I'm dealing with quite the same pressures though, at the very least its a significantly smaller system. For the time being I'm just going to put together a quick scrubby box though and hope it works good enough to not make my house toxic
  • Varine Varine:
    I mean I don't use this enough to pose any significant danger I don't think, but I would still rather not be throwing styrene all over the air
  • The Helper The Helper:
    New dessert added to recipes Southern Pecan Praline Cake https://www.thehelper.net/threads/recipe-southern-pecan-praline-cake.193555/
  • The Helper The Helper:
    Another bot invasion 493 members online most of them bots that do not show up on stats
  • Varine Varine:
    I'm looking at a solid 378 guests, but 3 members. Of which two are me and VSNES. The third is unlisted, which makes me think its a ghost.
    +1
  • The Helper The Helper:
    Some members choose invisibility mode
    +1
  • The Helper The Helper:
    I bitch about Xenforo sometimes but it really is full featured you just have to really know what you are doing to get the most out of it.
  • The Helper The Helper:
    It is just not easy to fix styles and customize but it definitely can be done
  • The Helper The Helper:
    I do know this - xenforo dropped the ball by not keeping the vbulletin reputation comments as a feature. The loss of the Reputation comments data when we switched to Xenforo really was the death knell for the site when it came to all the users that left. I know I missed it so much and I got way less interested in the site when that feature was gone and I run the site.
  • Blackveiled Blackveiled:
    People love rep, lol
    +1
  • The Helper The Helper:
    The recipe today is Sloppy Joe Casserole - one of my faves LOL https://www.thehelper.net/threads/sloppy-joe-casserole-with-manwich.193585/
  • The Helper The Helper:
    Decided to put up a healthier type recipe to mix it up - Honey Garlic Shrimp Stir-Fry https://www.thehelper.net/threads/recipe-honey-garlic-shrimp-stir-fry.193595/
  • The Helper The Helper:
    Here is another comfort food favorite - Million Dollar Casserole - https://www.thehelper.net/threads/recipe-million-dollar-casserole.193614/

      The Helper Discord

      Members online

      No members online now.

      Affiliates

      Hive Workshop NUON Dome World Editor Tutorials

      Network Sponsors

      Apex Steel Pipe - Buys and sells Steel Pipe.
      Top