World Russian sailor drinks half a litre of rum before crashing 7,000-ton ship at full speed into Scotland

tom_mai78101

The Helper Connoisseur / Ex-MineCraft Host
Staff member
Reaction score
1,663
A Russian officer on watch when a 423ft cargo ship ran aground at full speed in Scotland had drunk half a litre of rum before taking up his post, an investigation has found.

The Lysblink Seaways vessel was travelling from Belfast to Skogn in Norway with a cargo of paper when it became stuck off the west coast of Scotland near Kilchoan in the Ardnamurchan peninsula on 18 February this year.

The chief officer on watch, a 36-year-old Russian, had consumed half a litre of rum in his cabin before taking up his shift as the sole officer on watch at midnight, but had “become inattentive due to the effects of alcohol consumption”.

His actions led the ship to run aground at full speed into the rocky foreshore, where it remained for two days during bad weather.

It resulted in such bad damage to the ship that the vessel had to be scrapped, while damage to the hull and some fuel tanks led to 25 tonnes of marine gas oil entering the water, a report from the Marine Accident Investigation Branch (MAIB) found.


Driving under the influence is serious enough already. Driving a boat onto land while under the influence is on a whole another level.
 
Last edited by a moderator:

Varine

And as the moon rises, we shall prepare for war
Reaction score
805
What do you expect? They are Russian - the land was drunk and drove into them. I mean, they Scottish fucks are so god damn drunk they spill 90% of their Guinness and Jameson, you think earth ain't feeling it yet? Sheep shaggin' bastards.
 

KMilz

You can change this now in User CP.
Reaction score
141
Did this only happen because it was rum instead of vodka? 'Cuz half a 'litre' sounds like an everyday thing where Russians are concerned.
 

Varine

And as the moon rises, we shall prepare for war
Reaction score
805
That's why it wasn't the Russian's fault. It was those fucking Scotts.
 
General chit-chat
Help Users
  • No one is chatting at the moment.
  • Varine Varine:
    I ordered like five blocks for 15 dollars. They're just little aluminum blocks with holes drilled into them
  • Varine Varine:
    They are pretty much disposable. I have shitty nozzles though, and I don't think these were designed for how hot I've run them
  • Varine Varine:
    I tried to extract it but the thing is pretty stuck. Idk what else I can use this for
  • Varine Varine:
    I'll throw it into my scrap stuff box, I'm sure can be used for something
  • Varine Varine:
    I have spare parts for like, everything BUT that block lol. Oh well, I'll print this shit next week I guess. Hopefully it fits
  • Varine Varine:
    I see that, despite your insistence to the contrary, we are becoming a recipe website
  • Varine Varine:
    Which is unique I guess.
  • The Helper The Helper:
    Actually I was just playing with having some kind of mention of the food forum and recipes on the main page to test and see if it would engage some of those people to post something. It is just weird to get so much traffic and no engagement
  • The Helper The Helper:
    So what it really is me trying to implement some kind of better site navigation not change the whole theme of the site
  • Varine Varine:
    How can you tell the difference between real traffic and indexing or AI generation bots?
  • The Helper The Helper:
    The bots will show up as users online in the forum software but they do not show up in my stats tracking. I am sure there are bots in the stats but the way alot of the bots treat the site do not show up on the stats
  • Varine Varine:
    I want to build a filtration system for my 3d printer, and that shit is so much more complicated than I thought it would be
  • Varine Varine:
    Apparently ABS emits styrene particulates which can be like .2 micrometers, which idk if the VOC detectors I have can even catch that
  • Varine Varine:
    Anyway I need to get some of those sensors and two air pressure sensors installed before an after the filters, which I need to figure out how to calculate the necessary pressure for and I have yet to find anything that tells me how to actually do that, just the cfm ratings
  • Varine Varine:
    And then I have to set up an arduino board to read those sensors, which I also don't know very much about but I have a whole bunch of crash course things for that
  • Varine Varine:
    These sensors are also a lot more than I thought they would be. Like 5 to 10 each, idk why but I assumed they would be like 2 dollars
  • Varine Varine:
    Another issue I'm learning is that a lot of the air quality sensors don't work at very high ambient temperatures. I'm planning on heating this enclosure to like 60C or so, and that's the upper limit of their functionality
  • Varine Varine:
    Although I don't know if I need to actually actively heat it or just let the plate and hotend bring the ambient temp to whatever it will, but even then I need to figure out an exfiltration for hot air. I think I kind of know what to do but it's still fucking confusing
  • The Helper The Helper:
    Maybe you could find some of that information from AC tech - like how they detect freon and such
  • Varine Varine:
    That's mostly what I've been looking at
  • Varine Varine:
    I don't think I'm dealing with quite the same pressures though, at the very least its a significantly smaller system. For the time being I'm just going to put together a quick scrubby box though and hope it works good enough to not make my house toxic
  • Varine Varine:
    I mean I don't use this enough to pose any significant danger I don't think, but I would still rather not be throwing styrene all over the air

      The Helper Discord

      Members online

      No members online now.

      Affiliates

      Hive Workshop NUON Dome World Editor Tutorials

      Network Sponsors

      Apex Steel Pipe - Buys and sells Steel Pipe.
      Top