youtube stops playing clip after 2 seconds.

master maste

master maste

New Member
Reaction score
32
When I go onto www.youtube.com and play a clip it stops after 2 or 3 seconds and to keep playing it you need to click on the progress bar at the bottom for another 2 or 3 seconds. . . got any ideas on what is wrong and how I can fix it?

btw it works for all clips even ones that arent in youtube.
 
Thats a YouTube bug, not your computer.

It's due to overfull bandwidth use on their end.
 
you sure because its happened for not just youtube.
(lol the other clips are probably linked with youtube :p ) kk thanks.
 
Interestingly enough, I've seen this happen quite a bit when attempting to play back YouTube videos on the Wii (Opera browser), much more than when I'm just on my Mac or work PC. That seems off if it's just merely on YouTube's end.
 
I see a lot of people are having problems with this. I found the culprit to be my Plantronics bluetooth headset. It has a USB-transmitter plugin and when i pull this out the movie continues. Put it in and it stops after 2 secs. But I should like to know the reason for this as I like using the headset for listening.

master maste said:
When I go onto www.youtube.com and play a clip it stops after 2 or 3 seconds and to keep playing it you need to click on the progress bar at the bottom for another 2 or 3 seconds. . . got any ideas on what is wrong and how I can fix it?

btw it works for all clips even ones that arent in youtube.
Click to expand...
 
You must log in or register to reply here.
General chit-chat
Help Users
  • No one is chatting at the moment.
  • Varine Varine:
    I'm now realizing I could have cut out like 99% of this print and it would have been fine cuz I just need to see if a frame will fit over an LCD
  • Varine Varine:
    Oh well
  • Varine Varine:
    I'm not an engineer
  • Varine Varine:
    Although this filament is kind of expensive, I should probably be a bit more wary of that.
  • The Helper The Helper:
    I love the whole concept of 3D Printers and am very happy you have one so I can hear about them
  • The Helper The Helper:
    www.facebook.com

    897K views · 27K reactions | Follow for funny clips #comedy #craig #ferguson #rizz #funny #talkshow #killtonypodcast #killtony #funny #fyp #podcasting #reels2024 #comedy #killtonypodcast #killtony #comedian #comedy #funny #standupcomedy #memes #expl

    Follow for funny clips #comedy #craig #ferguson #rizz #funny #talkshow #killtonypodcast #killtony #funny #fyp #podcasting #reels2024 #comedy #killtonypodcast #killtony #comedian #comedy #funny...
    www.facebook.com www.facebook.com
  • Varine Varine:
    I have a couple of them, but I only have room for one to be set up at the moment
  • Varine Varine:
    So I picked the biggest one. When I bought it, I didn't realize that they used a lot of proprietary parts. So, I want to use these Volcano nozzles that are really cheap and easy to find instead of what they have, which are like, modified Volcano nozzles
  • Varine Varine:
    They are just a little bit longer than the regular ones. Like, we're talking .5mm or some shit. But that little bit makes the nozzle just long enough to extrude past the rest of the hardware on the extrusion system, I can't find my notes on it but I think it's like a .25mm gap from the end of the nozzle to the bed mesh sensor. Very small.
  • Varine Varine:
    So I bought a bunch of different parts to try and figure out how to make this work, and in the process changed some of the electrical components like the thermistors, but never got around to figuring out how to make the firmware account for the different hardware. Resulting in it not interpreting the voltage change to mean that the thermistor was above temperature, so it didn't shut off the heating core and it just kept pumping heat out
  • Varine Varine:
    I have most of the stuff I need to build an enclosure so I can heat the chamber for different plastics that need to have a pretty consistent temperature through the whole model, and then I can get my other ones set up too. I have a shitty Ender but that one is super easy to modify, but it's also very outdated and kind of a nightmare to work with. I think I'm going to cannibalize it for parts and just run my big one and another little one.
  • Varine Varine:
    I think I solved my problem with digitizing reels tho!
  • Varine Varine:
    Like Super 8 reels. Actual equipment to do it is like, thousands and thousands of dollars, and the cheap ones are useless, so I'm trying to build one so I can just use the same camera I use for slides and negatives. Much cheaper
  • Varine Varine:
    Anyway, it kind of works, but the take up reel is kind of tricky because you need to spin it directly to wind the tape onto it. And as it fills, you need to slow it down, and that's kind of complicated. More complicated than I wanted to try and account for, anyway.
  • Varine Varine:
    So I have the first motor that has gearing pull it from the original reel, through a set of pullies to keep some tension, and then a second motor synced with the first to guide it through the projection port so I can capture the images
  • Varine Varine:
    All that's easy enough, I just need to make sure I don't get too much force onto the film itself so I don't accidentally tear it.
  • Varine Varine:
    Then I think my solution to the take up reel is to have a kind of dancing lever on a spring in between two limit switches
  • Varine Varine:
    So, as the tape comes towards the take up reel and makes slack, that lever is pulled up by a spring to keep the tension on the film, it hits a limit switch to engage the take up reel motor at some point, and as that winds in the film, the film pushes the lever back down to a second limit switch to disengage the motor again. Slack builds up, spring pulls it back, ad infinitum
  • Varine Varine:
    Well, until the reel is empty anyway.
  • Varine Varine:
    I'm guessing it's going to be much harder than I feel like it is going to be right now, but I think it's a pretty elegant solution that doesn't rely on software to control it. The less software I need to use the better
  • Varine Varine:
    I'm just not a very good programmer, as much as I want to be I suck at it
  • The Helper The Helper:
    Programming that printer is going to be similar to programming a big machine like in a machine shop. There is good money in programming CNC machines.
  • The Helper The Helper:

    Facebook

    www.facebook.com www.facebook.com
    +1
  • Varine Varine:
    They are pretty similar, but this one is much less involved than a real CNC. A lot less moving parts
     +1
  • The Helper The Helper:
    Happy Monday!

      The Helper Discord

      Staff online

      Members online

      Online now:
      450 (members: 2, guests: 448)

      Share this page

      Affiliates

      Hive Workshop NUON Dome World Editor Tutorials

      Network Sponsors

      Apex Steel Pipe - Buys and sells Steel Pipe.
      Top