Well, I have been playing LoL too much to remember how creep pull in dota works but in LoL, minions are constantly being given orders, thus it doesn't matter that the attack command works until the target dies, because in less than 5 seconds the unit will be given a new order. Here's how it works:
Everytime a nearby unit is attacked, there is a priority check.
First, it checks if the new threat is higher than the creep's current target. Heres the order of priorities:
1. An enemy champion designated by a call for help from an allied champion.
2. An enemy minion designated by a call for help from an allied champion.
3. An enemy minion designated by a call for help from an allied minion.
4. An enemy turret designated by a call for help from an allied minion.
5. An enemy champion designated by a call for help from an allied minion.
6. The closest enemy minion.
7. The closest enemy champion.
For example, if a hero attacks a minion (#5), all nearby minions who are doing #6, 7, or nothing (simply walking around) will target the hero. But then if a minion allied to the hero attacks an enemy hero, that becomes priority #2, so all those minions who were targetting the first hero will try and kill the minion who's attacking their allied hero.
As for towers, the only place they appear is number 4. In other words, if there is a team 2 tower (priority #4) and a team 2 hero (priority #5) next to each other, no team 2 minions, the team 1 minions will target the tower, because if both the team 2 hero and tower target the team 1 minions, #4 has priority. But if there is a nearby team 1 hero and the team 2 hero decides to attack him (becomes priority #1), the team 1 minions will change target and priorize the team 2 hero.
One last thing, if a "threat" stops attacking its target for like 3 seconds, its priority will fall to 6 or 7 according to if its a champion or minion.
In short, what I just explained could be easily done, even with GUI (though differencing #6 and 7 may be hard, but then again you can just ignore those and keep only the 5 first priorities, as they are the most important)
Signatures can be edit in your account profile. As for the old stuffs, I'm thinking it's because Blizzard is now under Microsoft, and because of Microsoft Xbox going the way it is, it's dreadful.
@tom_mai78101 I must be blind. If I go on my profile I don't see any area to edit the signature; If I go to account details (settings) I don't see any signature area either.
You can get there if you click the bell icon (alerts) and choose preferences from the bottom, signature will be in the menu on the left there https://www.thehelper.net/account/preferences
I bought an Ender 3 during the pandemic and tinkered with it all the time. Just bought a Sovol, not as easy. I'm trying to make it use a different nozzle because I have a fuck ton of Volcanos, and they use what is basically a modified volcano that is just a smidge longer, and almost every part on this thing needs to be redone to make it work
So, 2.5mm longer. But the thing that measures the bed is about 1.5mm above the nozzle, so if I swap it with a volcano then I'm 1mm behind it. So cool, new bracket to swap that, but THEN the fan shroud to direct air at the part is ALSO going to be .5mm to low, and so I need to redo that, but by doing that it is a little bit off where it should be blowing and it's throwing it at the heating block instead of the part, and fuck man
I didn't realize they designed this entire thing to NOT be modded. I would have just got a fucking Bambu if I knew that, the whole point was I could fuck with this. And no one else makes shit for Sovol so I have to go through them, and they have... interesting pricing models. So I have a new extruder altogether that I'm taking apart and going to just design a whole new one to use my nozzles. Dumb design.
Can't just buy a new heatblock, you need to get a whole hotend - so block, heater cartridge, thermistor, heatbreak, and nozzle. And they put this fucking paste in there so I can't take the thermistor or cartridge out with any ease, that's 30 dollars. Or you can get the whole extrudor with the direct driver AND that heatblock for like 50, but you still can't get any of it to come apart