Step by Step instructions to Open Warcraft 3 Viewer
(Obligatory Disclaimer Note: these instructions are for Right-handed mouse holding people only. Sorry. I feel like discriminating against Lefties. Use your brains you lazy Lefties. Dont like it? Call my lawyer.)
.02) Put hand on mouse.
.03) Push mouse around with hand. Might like to try sideways and/or backwards and forwards until the cursor hovers over the blue link. I don't know of many mouses that can do Z height yet.
.04) Hold hand holding mouse with other hand.
.05) Lift hand holding mouse "right index finger" and extend (SLOWLY! We dont want you to strain a muscle). Hover tip of "right index finger" over "left mouse button."
.06) Pause finger, release hand holding hand holding mouse and extend ex-hand holding hand holding mouse to your left-hand side of the keyboard where the coffee cup is. Grab coffee* and take a swig, since you will need to recharge after all that effort.
Hereafter repeat steps .02 - .06 as necessary to complete the following tasks. Might want to consider boiling the Water jug/kettle/pot at this point. To understand how to do that, please refer to one of the manymanuals on Boiling Water, not made by this author.
1.) Click the left mouse button on blue link. (Supplementary Leftie Freebie Note follows): Or right mouse button if you have mouse controls swapped.
2.) Select the location to download to. I suggest Desktop, unless you have some sort of "downloads" folder that you regularly save things to.
3.) Extract the program that is connected to the blue link, inside the zip file after pushing your mouse over said blue link. To understand how to Extract, please download and read one of the many "unzipper" programs available for your convenience. I like this one "7-Zip". Specifically you will need to read up on "Extracting." It's in there somewhere.
4.) Run the setup program, if it is included. (Supplementary Leftie Freebie Note follows): Otherwise known as "Install". If there is no install, You might be screwed. In that case you will have to view this manual.
.06) (Obligatory Health and Safety Break)
5.) Please refer to steps .02 - .06 to Run the program. Usually labeled *.exe. In this case, (since this is a <refer Title of Article> the program is "Warcraft 3 Viewer.exe".) **
6.) If you have followed the instruction in this manual you should successfully be looking at a blue background(ed) screen that is displayed inside the aforementioned hand holding hand holding mouse being pushed after blue link is click and program is extracted and run. If not, then repeat steps .00 through 5. until a satisfactory result is complete.
>Last post
What the heck did you write that now .. "/ Good but .. eermh nothing.. good
>Push mouse around with hand. Might like to try sideways and/or backwards and forwards until the cursor hovers over the blue link. I don't know of many mouses that can do Z height yet.
Hahaha
Signatures can be edit in your account profile. As for the old stuffs, I'm thinking it's because Blizzard is now under Microsoft, and because of Microsoft Xbox going the way it is, it's dreadful.
@tom_mai78101 I must be blind. If I go on my profile I don't see any area to edit the signature; If I go to account details (settings) I don't see any signature area either.
You can get there if you click the bell icon (alerts) and choose preferences from the bottom, signature will be in the menu on the left there https://www.thehelper.net/account/preferences
I bought an Ender 3 during the pandemic and tinkered with it all the time. Just bought a Sovol, not as easy. I'm trying to make it use a different nozzle because I have a fuck ton of Volcanos, and they use what is basically a modified volcano that is just a smidge longer, and almost every part on this thing needs to be redone to make it work
So, 2.5mm longer. But the thing that measures the bed is about 1.5mm above the nozzle, so if I swap it with a volcano then I'm 1mm behind it. So cool, new bracket to swap that, but THEN the fan shroud to direct air at the part is ALSO going to be .5mm to low, and so I need to redo that, but by doing that it is a little bit off where it should be blowing and it's throwing it at the heating block instead of the part, and fuck man
I didn't realize they designed this entire thing to NOT be modded. I would have just got a fucking Bambu if I knew that, the whole point was I could fuck with this. And no one else makes shit for Sovol so I have to go through them, and they have... interesting pricing models. So I have a new extruder altogether that I'm taking apart and going to just design a whole new one to use my nozzles. Dumb design.
Can't just buy a new heatblock, you need to get a whole hotend - so block, heater cartridge, thermistor, heatbreak, and nozzle. And they put this fucking paste in there so I can't take the thermistor or cartridge out with any ease, that's 30 dollars. Or you can get the whole extrudor with the direct driver AND that heatblock for like 50, but you still can't get any of it to come apart